Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
We have stumbled upon this article relating to How to Install a Bathtub Yourself down the page on the net and concluded it made sense to write about it with you over here.
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have currently bought a brand-new tub as well as don't need to transform the plan of your previous water pipes.
Your devices as well as product checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer provided backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least when as this will resolve it into its last position.
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, creating the water to permeate the wall surface between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can fracture fairly early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for finding the time to read our posting. Appreciated our post? Please share it. Help someone else check it out. Thank you for your time. Don't hesitate to pay a visit to our website back soon.
Visit Page
Report this page